|
|
Delta 36-T30 T2 30-Inch Fence and Rail System
|
List Price: $265.14
Our Price: $150.65
You Save: $ 114.49 ( 43% )
Availability:
Manufacturer: Delta
|
Average Customer Rating:  
|
|
Binding: Tools & Hardware
Brand: Delta
EAN: 0028877545561
Feature: Three-point T-square locking system with hairline pointer to assure fence is parallel to blade and accurate to within 1/64 of an inch, Fence securely clamps to both front tube and rear rail to better allow for fence attachments.
Label: Delta
Manufacturer: Delta
Model: 36-T30
Publisher: Delta
Studio: Delta
|
|
|
Features
|
Three-point T-square locking system with hairline pointer to assure fence is parallel to blade and accurate to within 1/64 of an inch, Fence securely clamps to both front tube and rear rail to better allow for fence attachments.
Extruded aluminum face attaches to solid-steel angle iron and tubing for years of continuous use
Easy-gliding, steel tube fence body to handle quick, repetitive cut-off work, precision ripping and squaring cuts.
Quick-removal fence can be located on either side of the blade for consistent ripping capabilities on left or right tilt saws
Additional rear hold-down support for use with jigs and featherboards
|
|
|
|
|
|
|
|
|
Spotlight customer reviews:
|
Customer Rating:
Summary: It got the job done!
Comment: Having "rescued" a saw from being thrown away, this fixed the problem of no fence and gave a possible addition to the garbage dump a longer life. The fence is precise and well-made, and fit perfectly.
Customer Rating: 
Summary: Nice Fence, Difficult to install on non Delta saw
Comment: I bought this fence after reading the reviews here at Amazon. The Delta website says it can be installed on other saws, I have a 20 year old Craftman saw that needed a fence update and I liked the price of this fence. The instructions for installation are very staight forward if your saw is the Delta saw that this fence is paired with. If you are installing it on any other saw, your on your own. None of the holes in my saw matched up with the holes in the fence rails. I had to drill and tap four of the holes because they lined up with cast bracing on the underside of the table, I only had 4 holes that did not have braces behind them. There is very little room for error when you drill your own holes because a 16th of an inch to high or to low and the fence will drag on the table or leave to big of a gap. Some of this gap can be corrected by moving to facing on the fence up or down, but I would recommend measuring very carefully before you drill. I wound up mocking up the whole system and clamping it to my saw to make sure I had the correct clearences before I did my final drilling and installation. I have about 3 hours in it so far. I will do the final adjustments on the fence angles tonight. Like I said, this looks like it's going to be a real nice fence, I just wish Delta would include better instructions for Non Delta installations. Plan on buying a 17/64" drill bit, a 5/16" drill bit, and a 8mm x 1.25 tap. If you wind up needing to drill into the rails (I did) you will need a counter sink as well, you might also buy 2 of the 5/16" bits, the rails are really hand on the bits. Take your time to get it right the first time and you should do fine, Good Luck.
Customer Rating:
Summary: Delta T-30
Comment: Fence works great. There is very little adjustments needed to the fence. Fence comes with side to sid tilt adjustments and Pendulum angle adjustments. Wood doesn't bind or kick back when ripping. This item was shipped and delivered on the date that was given.
Customer Rating:
Summary: Great fence
Comment: I installed this fence on a 10" Craftsman saw. Had to modify the factory holes in the front and rear angle iron. Took about 1hr to do this. Take your time and all goes well. This fence is a great value for the money. Major upgrade from the factory fence. Love it. Handle could be a bit better. Does not stay in the up position to move fence. I have to fix this.
5 Star product.
Customer Rating:
Summary: Great upgrade for any Table Saw
Comment: I should have done this years ago!! I adapted this fence to a 1941 Craftsman 10" tablesaw. This saw was left to me by my great grandfather. I have been fighting the wobbley Craftsman fence for years!!! I had to create a mounting plate out of 3" X 3/16 strip steel because the old Craftsman saw's cast iron table wasn't thick enough to meet the holes on the new fence's mounting channel. But once I got it mounted, the fence works great! Vary accurate and easy to adjust! Best $150 I have spent on a tool in a long time!
|
|
|
Editorial Reviews:
|
Includes Delta® 30" T2 Fence System - 36-T30, T-Square® Commercial Fence, Steel Guide Tube w/ Scale, Front & Rear Support Rails, Mounting Hardware.
|
|
|
|
|
|
